Font Conversion & Repair
Introduction
Suppose you wished to add a new font to TDM. You could build it either from scratch, or by modifying an existing font. That building could be done with direct metrics+bitmap editing.
Alternatively, you could start with a new or existing TrueType Font. For fresh creation or modification within the TrueType world, a font editor (e.g., FontForge) would be needed. Once the .ttf file is in hand, conversion tools create a draft of the required metrics+bitmap files.
With either approach, you should expect font completion to have a "long tail" of further "repair", particularly for non-ASCII characters. As of 2024, there are four tools of note:
For conversions
...from a TrueType font to TDM bitmaps (in .tga/.dds files) and metrics (in .dat binary files):
For repair of TDM metrics
- Refont - New in 2024
- Q3Font
- Font Patcher
Conversion and repair tools are briefly described further below. These are used in concert with bitmap editors (e.g., Gimp). Also, TGA-to-DDS image conversion may be done with the bitmap editor, or with separate tools.
Fidcal's Original Take
These are some rough notes [from 2009] about converting ttf fonts to doom3 and repairing if necessary.
My understanding is that ExportFontToDoom3 is more suitable than Q3Font for converting. It is what I used to convert a lot of TTF fonts. See notes with that tool as to how use it. But be aware of copyright issues if converting TTF fonts.
With ExportFontToDoom3 there were quite a few spacing errors. Q3Font I found a bit puzzling so never did any conversions (it may be better for all I know.) BUT it can convert the dat files to readables for editing and back again so I used Q3Font to fix the errors.
Geep adds: Check out newer Font Patcher and Refont to fix errors too.
Doom fonts have multiple dat files for each size. However, only the following are loaded by the code:
- fontImage_12.dat
- fontImage_24.dat
- fontImage_48.dat
The size 24 is used mostly by readables, while the menu uses 48 (the big headlines and the main menu) and 24 (settings and other headlines). This means it is not necessary to create other sizes, as these will be ignored, anyway.
Geep adds: see Font Files for a fuller, more recent treatment about font file usage. For more details about Fidcal's 2009 improvements to TDM fonts, see this forum thread.
Main Tools
- ExportFontToDoom3 is, as Fidcal says, the recommended method, if you want to start a Doom3/TDM font project by generating from a TrueType font.
- Q3Font is the traditional Windows utility program to fix Doom3/TDM fonts. Fidcal provides a simple example of using it. (Some of this info used to be here in Font Conversion & Repair; some is an update.)
- Refont is another command-line program, new in 2024, that handles some of Q3font's functionality, but is easier to use. This article includes a detailed comparison.
- Font Patcher details the font_patcher.pl utility, which is a preferred method (over Q3font) to fix and change fonts. Includes links to examples.
Cautionary Considerations
Usually convert only once
If a font was converted from TrueType and subsequently received tweaks and repairs to its DAT or DDS files (as is very common), then you never want to apply conversion again, because that will throw away all those time-consuming customizations.
When changing font metrics in the DAT File
General constraints on the values of font metrics in a DAT file are discussed in Font Metrics & DAT File Format.
Additional constraints on changing metrics of long-deployed fonts
Consider a particular TDM font that has been in use for a while, and likely incorporated into, say, the readables of many FMs. Suppose you'd like to improve a particular character within it, say, by adjusting its DAT metrics. Maybe the glyph is showing stray marks from adjoining characters in its bitmap.
It's generally safe to move the bitmap cell boundaries horizontally a pixel at a time, by changing x-axis corner metrics s & s2 together, keeping imageWidth unchanged. When you do that, generally the "pitch" value (which denotes an xOffset distance from the s edge to the layout origin) needs compensating adjustment, to keep the layout origin the same with respect to the glyph. (Note: if the glyph is abutted against the overall bitmap side boundary, this approach may not be viable; the alternative of bitmap surgery may be needed.)
More problematic would be changing the xSkip value that controls a character’s horizontal spacing. Why? A readable’s author may have designed a particular text layout and expect word-wraps at particular place. An enlarged xSkip may force the end of a readable’s paragraph off the page. Even a shortened xSkip might interfere, e.g., with "ASCII art", tabular presentation, or bullet-point-style indentations that rely on word-wrap within a paragraph instead of separated sentences. So, either forego such a change, or be prepared for difficult research into where and how the candidate font character is used across FMs, including in translation strings.
A change to ImageWidth in theory has similar concerns, but in the more limited context of affecting only the first character rendered in any given line. So shrinking it is far less likely to be a problem in practice.
For More
- I18N (Internationalization) introduces consideration for non-English languages.
- I18N - Charset details the TDM-specific character mapping for non-English languages. For instance, if you convert a Russian font, you need to move the character 0xFF to 0xB6, otherwise it will not show in the GUI or readables.
