Texturing Archways

From The DarkMod Wiki
Revision as of 19:36, 23 February 2008 by Baddcog (talk | contribs) (added link to patch arch page)
Jump to navigationJump to search

Originally written by Gildoran on http://forums.thedarkmod.com/topic/2507

I've figured out a way of seamlessly texturing arches so that the blocks are the exact size and shape you want, using patch-meshes. It's low-poly, using 2 tris for each trapezoidal block (assuming you only have one visible face per block), and doesn't require new textures. Since it wasn't obvious to me and stone archways might be common in TDM, I figured I'd ask if anybody might be interested in a tutorial for it. Here's an example shot of what it looks like:

Arch.jpg Arch2.jpg

This is the first tutorial I've ever written, so any suggested changes are welcome. I'm not always the best at explaining things. It's a walk-through on how to take an already existing material and make one side of an archway that is properly textured without seams. It assumes the material is of a brick/block texture.

Make an archway

Make an archway and decide how the blocks are going to be shaped/etc.

Texturing archways0.jpg

In the picture above, I gave the blocks alternating textures so it's easy to tell them apart.

Choose what material you want to use.

Make a large brush and apply the material to it. Then decide which set of blocks you want to use.

Texturing archways2.jpg

Assuming you want the texturing to be seamless, choose a row or column of blocks that wrap. I think it's best to choose a set of blocks that are roughly the same size and proportions as the blocks of your archway, so the textures end up getting distorted the least.

Resize the large Brush

Resize the large brush so that its borders end just slightly outside your chosen set of blocks.

Texturing archways3.jpg

This is merely to make step 4 easier.

Chop up the brush into several smaller ones

Chop up the brush into several smaller quadrilateral ones so that each brush matches up with one block in the texture. I recommend using the clip tool and SHIFT+ENTER to split the brush along the seams between blocks, then going back and vertex editing them so they exactly match the shape of the blocks in the texture.

Texturing archways1.jpg

It may be easier to see where the seams are if you turn on light rendering. Try to get the brushes to match the texture as closely as possible; I recommend using a grid-spacing of 1. Also, make sure that the first and last brush fit together perfectly without a texture seam.

For each block, make a simple patch mesh.

Vertex edit the patch mesh so that it matches the shape of its corresponding brush in the 2D window. Also, it is very important to make sure that it is in the same position as its corresponding brush in the 2D window. Then, select all the patch meshes, and copy the texture from the brushes by clicking on them with the middle mouse button.

Texturing archways4.jpg

This should cause your patch meshes to have the proper texturing, so you can repeat them without texture seams.

Clone your patch meshes as much as needed

Clone your patch meshes as much as needed and vertex edit them so they match the shape of the blocks of your archway.

Texturing archways5.jpg

You should end up with a bunch of patch meshes that act as one side of your archway being textured seamlessly. As a final touch, go into the surface editor, and turn on "subdivide patch" with horizontal and vertical at 1. If the texture looks distorted, you may need to increase the subdivisions, but that will result in more triangles being used.

This technique could be used again for the top and bottom of the archway if you want to construct it entirely out of patch meshes, or you could make it out of brushes and texture one side with caulk, then move the patch meshes so they're coplanar with the side of the archway.

Alternate method to texturing arches using patches: http://modetwo.net/darkmod/wiki/index.php/Patches#Trim_Arches