Patches

Introduction

A patch:

• is a two dimensional sheet with only one visible surface. It can be bent, curved and twisted in three dimensions but always remains a sheet. It produces better curves and textures better on them than multiple brushes.
• can also be a cylinder, great for pipes or bars.
• is a primitive - a child of the worldspawn entity. This means it is a direct offshoot of the game world and inherits any properties applied to the worldspawn. If you select a brush and look in the Entity Inspector you will see the worldspawn properties.
• may be parented to another entity when it will inherit its properties.
• will not seal against the void.
• is suitable for decals - textures such as stains to be placed over other surfaces.

Round and Softened Corners: Bevels

written by Fidcal

No matter how beautiful the texturing, a mathematically-sharp convex corner is likely to spoil it.

These can be rounded off nicely using a patch bevel. The same method can of course be used to produce larger rounded corners.

• Select the brush that forms the corner.
• Zoom in and set the grid to about 4 or 8. How rounded you want the corner will depend on the texture and other things. I crisp new brick wall might be better with a small rounded corner whereas old round stone blocks will take a larger curve. You can of course, use this method for very large curves where they are an architectural feature not merely a softening of a sharp edge.
• Press CTRL+X for Clipper or select on the left toolbar

• Click the two diagonals in order 0 then 1 as shown in the diagram so that the corner is to the right if 0 was 12 on a clock and 1 is 6.

• SHIFT+ENTER to split off the corner without deleting it
• ESC to deselect then exclusively select the corner triangle. This might be easier in camera view.

• Bevels are always created with their curve in the horizontal plane which is what we want here for a vertical corner (if you need a different orientation you have to rotate it after creation.)
• Select Patch -> Bevel
• If the bevel is facing the wrong way (in top view) then rotate it, grid snap if necessary to as shown in the image below. The bevel might not have the same number of faces as in the diagram. Don't worry. We set that separately anyway.

• Delete the original brush corner triangle that was the template for this bevel.
• Press SHIFT+S for patch inspector
• Click the check box 'Fixed Subdivision' else Doom might change the quality when optimising.
• In the 'Horizontal' input just below that in Patch Inspector set the value to 3 or 4. The higher the value the lower the game performance and beyond a certain value you cannot tell any difference so don't be tempted to go high. It's a matter of experience, judgement, how big the curve is, and the type of texture.

• Close the Patch Inspector and use ESC to deselect the bevel
• Use CTRL+SHIFT+ to select only the surface of the brush wall to one side of the bevel. Use a side where you do not want to have to re-align the texture on that wall, eg, there is a window further along and it might be awkward. This is because later, the wall texture on the OTHER side of the bevel may have to be realigned to the bevel.
• Use Edit -> Copy Shader or the key/mouse shortcut
• Press ESC to deselect and select the bevel again
• Use Edit -> Paste Shader (Natural) or the shortcut. Do NOT use the normal paste - nor normal paste followed by Natural in the Surface Inspector.
• The texture on the bevel should be aligned to that wall.
• Check texture alignment on the wall on the other side of the bevel and shift it in Surface Inspector as needed.

Hopefully that should now look far better:

Cylinders

by Baddcog

To create a cylindrical patch

• drag out a brush an ortho view. The cylinder will be created in the plane of the ortho view you cretaed the brush in. If you used the top view you will end up with a cylinder standing upright.
• with the brush selected choose the patch menu
• cylinder will give you a nice and round cylinder with one set of rows (lenghtwise). It will be the size of the brush you had selected.

'More cylinders' gives you more options: dense cylinder; a cylinder with 2 rows, very dense cylinder; a cylinder with 3 rows, square cylinder; a four sided cylinder. All patches are rendered smooth, so you can use a square cylinder and it will still have an almost round look to it in game as opposed to a square brush that will render flat and very square.

Other References

General patches tutorial: http://www.modwiki.net/wiki/Patch